BT5 下怎么安装NW362无线网卡驱动？
下面是readme.txt的说明本人对英语命令是小白，求大神们把步骤写的详细点！！！！不胜感激！！！
===============================================================================
Software Package - Component
===============================================================================
1. ReleaseNotes.doc
2. document/
3. driver source code
3.1 Makefile - to build the modules
3.2 Script and configuration for DHCP:
"wlan0dhcp"
"ifcfg-wlan0"
3.3 Example of supplicant configuration file:
"wpa1.conf"
3.4 Script to run wpa_supplicant
"runwpa"
3.5 Script to clean relative modules
"clean"
4. wpa_supplicant/wpa_supplicant-0.6.9_wps_patch_20100201.zip
The tool help the wlan network to communicate under the
protection of WPAPSK mechanism (WPA/WPA2) and add WPS patch
5. install.sh
Script to easy make 8192cu driver.
==================================================================================================================
User Guide(1) - connecting wireless networking using "Network Manager" GUI utility (For PC Linux)
==================================================================================================================
(1) Network Manager is a utility attempts to make use of wireless networking easy.
(2) Notes: if you want to use the following command-line method to connect wireless networking,
please disable the "Network Manager", because "Network Manager" will conflict with method of command line .
==================================================================================================================
User Guide(2) - Using the wpa_cli & wpa_supplicant tools (For embedded Linux)
==================================================================================================================
Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc
==================================================================================================================
User Guide(3) - Set wireless lan MIBs in Command Line (Legacy command - Not recommend)
==================================================================================================================
This driver uses Wireless Extension as an interface allowing you to set
Wireless LAN specific parameters.
Current driver supports "iwlist" to show the device status of nic
iwlist wlan0
where
parameter explaination
----------------------- -------------
Show available chan and freq freq / channel
Show and Scan BSS and IBSS scan
Show supported bit-rate rate / bit
For example:
iwlist wlan0 channel
iwlist wlan0 scan
iwlist wlan0 rate
Driver also supports "iwconfig", manipulate driver private ioctls, to set
MIBs.
iwconfig wlan0
where
parameter explaination constraints
----------------------- ------------- ------------------
Connect to AP by address ap
Set the essid, join (I)BSSessid
Set operation mode mode {Managed|Ad-hoc}
Set keys and security modekey/enc {N|open|restricted|off}
For example:
iwconfig wlan0 essid "ap_name"
iwconfig wlan0 ap XX:XX:XX:XX:XX:XX
iwconfig wlan0 mode Ad-hoc
iwconfig wlan0 essid "name" mode Ad-hoc
iwconfig wlan0 key 0123456789 open
iwconfig wlan0 key off
iwconfig wlan0 key restricted 0123456789
Note: Better to set these MIBS without GUI such as NetworkManager and be sure that our
nic has been brought up before these settings. WEP key index 2-4 is not supportted by
NetworkManager.
===============================================================================
Getting IP address (For User Guide(2) & User Guide(3))
===============================================================================
After start up the nic and connect to AP successfully, the network needs to obtain an IP address
before transmit/receive data.
This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"
command, or using DHCP.
If using DHCP, setting steps is as below:
(1)check if the WiFi had connected to an AP via "iwconfig" command
$> iwconfig
(2)run the script which run the dhclient
$> ./wlan0dhcp
or
dhcpcd wlan0
(Some network admins require that you use the
hostname and domainname provided by the DHCP server.
In that case, use
dhcpcd -HD wlan0)
===============================================================================
WPAPSK/WPA2PSK - using wpa_supplicant (For User Guide(3))
===============================================================================
Wpa_supplicant helps to secure wireless connection with the protection of
WPAPSK/WPA2PSK mechanism. Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc
===============================================================================
WPS - PIN & PBC methods
===============================================================================
(*) Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc
===============================================================================
Power Saving Mode
===============================================================================
(*) Please refer to the document/HowTo enable the power saving functionality.doc
页:
[1]