插上卡驱动加载完成后，输入命令dmesg 把最后有关网卡的部分贴图上来。
还有网卡的具体型号是什么？不是芯片，是厂家的型号。
[ 本帖最后由 minileaf 于 2008-9-5 13:20 编辑 ]
我的卡是在淘宝上买的,店家说这原来是Skype网络电话的一个AP的.
牌子ASUS,
上面只有这字样:
FCC ID : MSQU1
MODEL NO: U1
我这还有其Linux的驱动如方便,请加我的QQ: ２。７。１。６。８。８。３
我传给请，请你分析下。谢谢
Linux kernel driver for RTL8187/RTL8187B based WLAN cards
Copyright (c) 2004-2005, Andrea Merello
rtl8187b: Initializing module
rtl8187b: Wireless extensions version 22
rtl8187b: Initializing proc filesystem
rtl8187b: Reported EEPROM chip is a 93c46 (1Kbit)
rtl8187b: Card MAC address is 00:16:e3:63:fa:af
rtl8187b: Card reports RF frontend Realtek 8225
rtl8187b: WW:This driver has EXPERIMENTAL support for this chipset.
rtl8187b: WW:use it with care and at your own risk and
rtl8187b: WW:**PLEASE** REPORT SUCCESS/INSUCCESS TO Realtek
rtl8187b: This seems a legacy 1st version radio
rtl8187b: PAPE from CONFIG2: 0
rtl8187b: Driver probe completed
usbcore: registered new interface driver rtl8187b
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
rtl8187b: Card successfully reset
This is RTL8187 Reset procedure
Set chan.call ieee80211_start_bss.in start bss call check.<6>mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
rtl8180_close process
rtl8180_down process
RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe) RX Status Error!
RX process aborted due to explicit shutdown (fffffffe)
在这里，有我网卡的linux的驱动，要我用不来！看能不能参考这个，修改下你为我做的BT3下的驱动尼！谢谢
http://forum.anywlan.com/viewthread.php?tid=11930&extra=&frombbs=1
dmesg显示的信息和我的网卡一样,应该能用.
用iwlist wlan0 scan 看看有没有找到ap.
上面地址的驱动在Bt3下编译要出错！
[ 本帖最后由 minileaf 于 2008-9-5 23:28 编辑 ]
还没睡觉，看来是个夜猫:lol
root@bt:~# iwlist wlan0 scan
wlan0 Failed to read scan data : Operation not permitted
看来得找其他driver。
辛苦了朋友:handshake
他提到了编程器，应该是把EEPROM取了下来，备份后，再重新写入ID到EEPROM。然后将EEPROM焊接回网卡。需要设备和纯熟的手艺！
以前一直以为你的网卡是rtl8187b的，现在知道是rtl8187L的，看来还是有办法的。想想，想想，再想想！
这个驱动应该可以了，8187L的驱动很好找，还是打了可以调高功率的补丁的，试试了！
原帖由 recher 于 2008-9-1 01:58 发表 http://forum.anywlan.com/images/common/back.gif
我的8187b为啥 bt3里面显示所有pwr都为0？？
谁解决送8187B的网卡一个~~~
BT3 下不能完美支持，有时你用 windows 下测 有 90% 的信号，到 bt3 下有时就是不支持注入，
有时 windows 下 50 信号的 AP bt3 又可以支持 注入
个人认为原因是因为，驱动支持不好，
解决方法 1.更新更好的驱动
2.直接换卡，这张拿来上网用