hijk1 发表于 2015-3-25 21:54
可以刷openwrt固件了
亲您有WPB-5000-I-T-GN-27P openwrt固件能发个给我么540734850@qq.com
WPB-5000-I-T-GN-27P
U-Boot 1.1.4 (May 31 2012 - 19:28:20)
AP91 (ar7240) U-boot
DRAM:
sri
ar7240_ddr_initial_config(146): python ddr init
#### TAP VALUE 1 = 9, 2 = a
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 262k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
id read 0x100000ff
flash size 16777216, sector count = 256
Flash: 16 MB
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Hit any key to stop autoboot:2 1 0
read image version 121 size = 0x006fc010
checking crc...
crc ok!
boot_partition : 1
## Booting image at 9f050010 ...
Image Name: Linux Kernel Image
Created: 2013-02-02 8:32:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 933212 Bytes = 911.3 kB
Load Address: 80002000
Entry Point:8028d000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8028d000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
Booting AR7240(Python)...
found squashfs at 150010
Starting pid 14, console /dev/ttyS0: '/etc/rc.d/rcS'
Unlocking uboot-env ...
Reading from uboot-env to /var/tmp/bootcfg ...[ ]
Install gpio modules
bconf = 00:1F:6F:34:9D:B0
Install wifi modules
wifi1 no private ioctls.
SIOCGIFFLAGS: No such device
SIOCSIFTXQLEN: No such device
wlan0
bconf = 00:1F:6F:34:9D:B0
2.4G Management IP(192.168.10.228) Subnet(255.255.255.0) is old, use new default value!
wlan0
bconf = 00:1F:6F:34:9D:B0
Install wan modules
udhcpc (v0.9.9-pre) started
Jan1 00:00:07 udhcpc: udhcpc (v0.9.9-pre) started
Sending discover...
Jan1 00:00:08 udhcpc: Sending discover...
Starting pid 122, console /dev/ttyS0: '/sbin/getty'
WPB-5000 login: Sending discover...
怎么进入设置界面
扫描的结果怎么连接
SSID 空的
用户名 management密码management 不能连接
这个不好玩啊
空SSID 这么连呢 求助
本帖最后由 xqsf 于 2016-4-12 14:48 编辑
wang7268 发表于 2016-1-6 21:32
WPB-5000-I-T-GN-27P
U-Boot 1.1.4 (May 31 2012 - 19:28:20)
请问刷的是什么固件？还是只是刷了uboot？
欧阳雄风 发表于 2013-4-25 09:14
选择PPPOE上网设置好以后，状态中显示已经连接。
笔记本，台式机需要选择自动获得IP。
这AP可卖多少钱，带独立放大模块那种的
15一个 买了3个无线信号没有想象的那么好 和家用路由器没区别 可能是天线没有匹配好
想刷dd固件了 不知道大神是怎么刷的 Dlink DIR-825 求编程器固件 折腾万岁 谢谢！