eduedu530 发表于 2014-6-5 16:34

wr842 v4.1 ttl 接线图-测试通过。

本帖最后由 eduedu530 于 2014-6-6 11:06 编辑

wr842 v4.1 ttl 接线图-测试通过。

WR842N_V4 .1         
CPU    QCA9531 MIPS 24Kc 550MHz   300Mbps24Kc系列支持多线程，8级流水   
(QCA9533)      (QCA9558 MIPS 74Kc 720 MHz)

   25Q80BVS1G winbond华邦SPI存储器 1MB          A3S64D40GTP-50 Zentel力积DDR SDRAM内存 8MB

这个跟4.0版的CPU 有点不同。4. 0 是QCA9531

wr842 v4.1 ttl 接线 步骤：
1、短接R50，R32 两个电阻。
2、J3 四个接口（LED指示灯正对自己） 从左到右分别是：VCC 、GND、TX、 RX、

OK

附TTL信息图

U-Boot 1.1.4 (Build from LSDK- at Mar 21 2013 - 10:06:47)
ap143 - Honey Bee 1.1
DRAM:   8 MB
Top of RAM usable for U-Boot at: 80800000
Reserving 128k for U-Boot at: 807dc000
Reserving 132k for malloc() at: 807bb000
Reserving 44 Bytes for Board Info at: 807bafd4
Reserving 36 Bytes for Global Data at: 807bafb0
Reserving 128k for boot params() at: 8079afb0
Stack Pointer at: 8079af98
Now running in RAM - U-Boot at: 807dc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x14
flash size 4MB, sector count = 256
Flash:1 MB
Using default environment
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 78:a1:06:55:b8:28
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 78:a1:06:55:b8:29
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4b97a100
Hit any key to stop autoboot:0
vxWorks.bin from =0x4f060, len=0x8613f
Uncompressing...done
                                    Attaching interface lo0... done
Rx clbufs 768 each of size 1660
ATHRS27: resetting s27
ATHRS27: s27 reset done
ATHRS27:Port status register read 2:7E
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (0):862
ATHRS27:S27 ATHR_PHY_ID1(0) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS(0) :10
ATHRS27:S27 ATHR_PHY_STATUS(0) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (1):862
ATHRS27:S27 ATHR_PHY_ID1(1) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS(1) :10
ATHRS27:S27 ATHR_PHY_STATUS(1) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (2):862
ATHRS27:S27 ATHR_PHY_ID1(2) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS(2) :10
ATHRS27:S27 ATHR_PHY_STATUS(2) :7949
ATHRS27:S27 ATHR_PHY_FUNC_CONTROL (3):862
ATHRS27:S27 ATHR_PHY_ID1(3) :4d
ATHRS27:S27 ATHR_PHY_SPEC_STATUS(3) :10
ATHRS27:S27 ATHR_PHY_STATUS(3) :7949
ATHRS27:S27 CPU_PORT_REGISTER :f0
ATHRS27:S27 PORT_STATUS_REGISTER0:fe
ATHRS27:S27 PORT_STATUS_REGISTER1:1280
ATHRS27:S27 PORT_STATUS_REGISTER2:1280
ATHRS27:S27 PORT_STATUS_REGISTER3:1280
ATHRS27:S27 PORT_STATUS_REGISTER4:1280
ATHRS27:S27 PORT_CONTROL_REGISTER0 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER1 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER2 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER3 :4004
ATHRS27:S27 PORT_CONTROL_REGISTER4 :4004
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
ae1 Verify MAC address 28B85506 A1780000
sb = 78 A1 06 55 B8 28
ATHRS27:ATHRS27:OPERATIONAL_MODE_REG0:40
ATHRS27:ATHRS27:REG 0x4-->:40
ATHRS27:ATHRS27:REG 0x2c-->:fe7f007f
ATHRS27:ATHRS27:REG 0x8-->:10000000
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
ATHRS27:athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
ATHRS27:athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
ae0 Verify MAC address 29B85506 A1780000
sb = 78 A1 06 55 B8 29

                                    Version2.0
                            Software Platform for PNE2.2
            Copyright(C) 2001-2011 by TP-LINK TECHNOLOGIES CO., LTD.
                      Creation date: Jan 20 2014, 15:15:24
# Moduler MODULER-CONTROL: start working.

All config data size = 22244, srart address= 0x804853a0.
Moduler MODULER-CONTROL: size = 16, srtart address = 0x804853a0.
Moduler SYSTEM-LOG: size = 280, srtart address = 0x804853b0.
Moduler TDDP-AGENT: size = 0, srtart address = 0x804854c8.
Moduler OEMDEF: size = 592, srtart address = 0x804854c8.
Moduler BRIDGE: size = 0, srtart address = 0x80485718.
Moduler ACCOUNT: size = 40, srtart address = 0x80485718.
Moduler WEB-V4: size = 0, srtart address = 0x80485740.
Moduler wizard: size = 0, srtart address = 0x80485740.
Moduler OPMODE: size = 4, srtart address = 0x80485740.
Moduler LAN: size = 16, srtart address = 0x80485744.
Moduler UPnP: size = 0, srtart address = 0x80485754.
Moduler WLAN: size = 3380, srtart address = 0x80485754.
Moduler MAC-CLONE: size = 0, srtart address = 0x80486488.
Moduler DHCPS: size = 1964, srtart address = 0x80486488.
Moduler IF-NAT: size = 0, srtart address = 0x80486c34.
Moduler WAN: size = 4, srtart address = 0x80486c34.
Moduler LINKMODE: size = 4, srtart address = 0x80486c38.
Moduler STATIC-IP: size = 32, srtart address = 0x80486c3c.
Moduler DHCPC: size = 104, srtart address = 0x80486c5c.
Moduler PPPoE: size = 596, srtart address = 0x80486cc4.
Moduler VIRTSVR: size = 904, srtart address = 0x80486f18.
Moduler IGDV2: size = 4, srtart address = 0x804872a0.
Moduler DMZ-HOST: size = 8, srtart address = 0x804872a4.
Moduler STATIC-ROUTER: size = 328, srtart address = 0x804872ac.
Moduler Statistics: size = 20, srtart address = 0x804873f4.
Moduler AccessCtrl: size = 10860, srtart address = 0x80487408.
Moduler Security: size = 40, srtart address = 0x80489e74.
Moduler ARPBIND: size = 648, srtart address = 0x80489e9c.
Moduler ADDITIONDNS: size = 0, srtart address = 0x8048a124.
Moduler DNS-PROXY: size = 0, srtart address = 0x8048a124.
Moduler DDNS: size = 1740, srtart address = 0x8048a124.
Moduler IPQOS: size = 572, srtart address = 0x8048a7f0.
Moduler LOGIN-PASSWORD: size = 0, srtart address = 0x8048aa2c.
Moduler USER-REBOOT: size = 0, srtart address = 0x8048aa2c.
Moduler RESET: size = 0, srtart address = 0x8048aa2c.
Moduler DIAGNOSTIC: size = 0, srtart address = 0x8048aa2c.
Moduler BAKNRESTORE: size = 0, srtart address = 0x8048aa2c.
Moduler HTTP-FIRMWARE: size = 0, srtart address = 0x8048aa2c.
Moduler IGMP: size = 4, srtart address = 0x8048aa2c.
Moduler ANTI-SNIFFER: size = 0, srtart address = 0x8048aa30.
Moduler SNTPC: size = 84, srtart address = 0x8048aa30.
Moduler SYSTEM-LOG: start working.
Moduler TDDP-AGENT: start working.
Moduler OEMDEF: start working.
Moduler BRIDGE: start working.
Moduler ACCOUNT: start working.
Moduler WEB-V4: start working.
Moduler wizard: start working.
Moduler OPMODE: start working.
Moduler LAN: start working.
Moduler UPnP: start working.
Moduler WLAN: start working.
Enterprise mode: 0x00000000
Restoring Cal data from Flash
correct CRC of the calData stored in flash is 0x3b5cb2a0
actual CRC of the calData stored in flash is 0x3b5cb2a0
if no temp comp, enable it.
base_eep_header.feature_enable = 0x4d.
base_eep_header.txrxgain = 0x11.
modal_header_2g.temp_slope = 0x13.
modal_header_5g.temp_slope = 0x44.
base_ext2.temp_slope_low = 0x14.
802F6500:02 02 00 03 7F 4E C0 00 - 00 00 00 00 00 00 00 00      ....N.. ........
802F6510:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 1F 00      ........ ........
802F6520:33 02 00 00 00 00 04 00 - 65 00 4D 00 03 00 08 FF      3....... e.M.....
802F6530:11 00 00 00 00 10 01 10 - 00 22 22 02 00 50 01 50      ........ .""..P.P
802F6540:01 50 01 00 00 00 00 00 - 00 13 00 64 7D A4 AF 00      .P...... ...d}...
802F6550:FF 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6560:0E 0E 03 00 2C E2 00 02 - 0E 1C 80 C0 80 0C 80 C0      ....,... ........
802F6570:80 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6580:00 00 00 00 00 00 00 00 - 00 00 70 89 A2 EA 00 86      ........ ..p.....
802F6590:00 00 00 EA 00 84 00 00 - 00 EA 00 89 00 00 00 EE      ........ ........
802F65A0:00 7B 00 00 00 EF 00 7A - 00 00 00 EF 00 7B 00 00      .{.....z .....{..
802F65B0:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F65C0:00 00 00 70 AC 70 89 AC - 70 89 AC 70 89 AC 28 28      ...p.p.. p..p..((
802F65D0:28 28 28 28 28 28 28 28 - 22 1E 28 28 22 1E 28 28      (((((((( ".((".((
802F65E0:22 1E 24 24 20 1E 1C 1A - 20 1E 1C 1A 20 20 1C 14      ".$$ ........
802F65F0:24 24 20 1E 1C 1A 20 1E - 1C 1A 20 20 1C 14 24 24      $$ ... . ....$$
802F6600:20 1E 1C 1A 20 1E 1C 1A - 20 20 1C 14 22 22 1E 1C       ... ...   ..""..
802F6610:1A 18 1E 1C 1A 18 20 20 - 1C 14 22 22 1E 1C 1A 18      ......   ..""....
802F6620:1E 1C 1A 18 20 20 1C 14 - 22 22 1E 1C 1A 18 1E 1C      ...... ""......
802F6630:1A 18 20 20 1C 14 11 12 - 15 17 41 42 45 47 31 32      ...... ..ABEG12
802F6640:35 37 70 75 9D A2 70 75 - A2 FF 70 75 A2 FF 7A 7F      57pu..pu ..pu..z
802F6650:93 98 70 75 AC B8 70 75 - AC 00 70 75 AC 00 7A 7F      ..pu..pu ..pu..z
802F6660:93 A2 70 75 AC 00 70 75 - AC 00 70 75 AC 00 7A 7F      ..pu..pu ..pu..z
802F6670:93 A2 3C 7C 3C 3C 3C 7C - 3C 3C 7C 3C 3C 7C 7C 3C      ..<|<<<| <<|<<||<
802F6680:3C 3C 3C 7C 3C 3C 3C 7C - 3C 3C 3C 7C 7C 3C 3C 7C      <<<|<<<| <<<||<<|
802F6690:3C 3C 3C 7C 3C 3C 3C 7C - 3C 3C 3C 7C 7C 7C 3C 7C      <<<|<<<| <<<|||<|
802F66A0:7C 7C 10 01 00 00 22 22 - 02 00 00 00 00 00 00 00      ||...."" ........
802F66B0:00 00 00 00 00 00 44 00 - 00 00 00 00 00 FF 00 00      ......D. ........
802F66C0:00 00 00 00 00 00 00 00 - 00 00 00 00 00 0E 0E 03      ........ ........
802F66D0:00 2D E2 00 02 0E 1C E0 - E0 F0 0C E0 E0 F0 6C 00      .-...... ......l.
802F66E0:00 00 00 00 00 00 00 00 - 00 14 00 00 00 00 00 00      ........ ........
802F66F0:00 00 00 00 00 00 00 4C - 54 68 78 8C A0 B9 CD 00      .......L Thx.....
802F6700:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6710:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6720:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6730:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6740:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6750:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6760:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6770:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00      ........ ........
802F6780:00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 4C      ........ .......L
802F6790:54 68 78 8C A0 B9 CD 4C - 58 68 8C B4 BD B9 CD 4C      Thx....L Xh.....L
802F67A0:58 68 8C B4 BD B9 CD 14 - 14 14 0A 14 14 14 0A 14      Xh...... ........
802F67B0:14 14 0A 14 14 14 0A 14 - 14 14 0A 14 14 14 0A 14      ........ ........
802F67C0:14 14 0A 14 14 14 0A 14 - 14 0A 0A 00 00 0A 0A 00      ........ ........
802F67D0:00 0A 0A 00 00 14 14 0A - 0A 00 00 0A 0A 00 00 0A      ........ ........
802F67E0:0A 00 00 14 14 0A 0A 00 - 00 0A 0A 00 00 0A 0A 00      ........ ........
802F67F0:00 14 14 0A 0A 00 00 0A - 0A 00 00 0A 0A 00 00 14      ........ ........
802F6800:14 0A 0A 00 00 0A 0A 00 - 00 0A 0A 00 00 14 14 0A      ........ ........
802F6810:0A 00 00 0A 0A 00 00 0A - 0A 00 00 14 14 0A 0A 00      ........ ........
802F6820:00 0A 0A 00 00 0A 0A 00 - 00 14 14 0A 0A 00 00 0A      ........ ........
802F6830:0A 00 00 0A 0A 00 00 14 - 14 0A 0A 00 00 0A 0A 00      ........ ........
802F6840:00 0A 0A 00 00 14 14 0A - 0A 00 00 0A 0A 00 00 0A      ........ ........
802F6850:0A 00 00 14 14 0A 0A 00 - 00 0A 0A 00 00 0A 0A 00      ........ ........
802F6860:00 14 14 0A 0A 00 00 0A - 0A 00 00 0A 0A 00 00 14      ........ ........
802F6870:14 0A 0A 00 00 0A 0A 00 - 00 0A 0A 00 00 14 14 0A      ........ ........
802F6880:0A 00 00 0A 0A 00 00 0A - 0A 00 00 14 14 0A 0A 00      ........ ........
802F6890:00 0A 0A 00 00 0A 0A 00 - 00 14 14 0A 0A 00 00 0A      ........ ........
802F68A0:0A 00 00 0A 0A 00 00 10 - 16 18 40 46 48 30 36 38      ........ ..@FH068
802F68B0:4C 5C 60 8C A0 B4 BD CD - 4C 5C 60 8C 90 B4 BD CD      L\`..... L\`.....
802F68C0:4E 56 5E 66 8E 96 AE BF - 4C 50 5C 68 8C B4 FF FF      NV^f.... LP\h....
802F68D0:4C 5C 8C B4 FF FF FF FF - 4E 5E 66 8E 9E AE FF FF      L\...... N^f.....
802F68E0:4C 50 54 5C 8C A0 B4 BD - 4C 5C 68 8C 98 B4 BD CD      LPT\.... L\h.....
802F68F0:4E 56 5E 8E 96 AE BF C7 - 7C 7C 7C 7C 7C 7C 7C 3C      NV^..... |||||||<
802F6900:7C 7C 7C 7C 7C 7C 7C 3C - 3C 7C 3C 7C 7C 7C 7C 7C      |||||||< <|<|||||
802F6910:3C 7C 7C 3C 7C 3C 3C 3C - 7C 7C 7C 3C 3C 3C 3C 3C      <||<|<<< |||<<<<<
802F6920:7C 7C 7C 7C 7C 3C 3C 3C - 7C 7C 7C 7C 7C 7C 7C 7C      |||||<<< ||||||||
802F6930:7C 7C 3C 7C 7C 7C 7C 3C - 7C 3C 7C 7C 7C 7C 3C 7C      ||<||||< |<||||<|
wlanSecFliterStart : install Wlan Sec filter.
Moduler MAC-CLONE: start working.
Moduler DHCPS: start working.
Moduler IF-NAT: start working.
Moduler WAN: start working.
Moduler LINKMODE: start working.
Set phy 4 link mode 0x01.
Moduler STATIC-IP: start working.
Moduler DHCPC: start working.
add net 0.0.0.0: gateway 169.254.184.40
Moduler PPPoE: start working.
Moduler VIRTSVR: start working.
Moduler IGDV2: start working.
Moduler DMZ-HOST: start working.
Moduler STATIC-ROUTER: start working.
Moduler Statistics: start working.
Moduler AccessCtrl: start working.
Moduler Security: start working.
Moduler ARPBIND: start working.
Moduler ADDITIONDNS: start working.
Moduler DNS-PROXY: start working.
Moduler DDNS: start working.
Moduler IPQOS: start working.
Moduler LOGIN-PASSWORD: start working.
Moduler USER-REBOOT: start working.
Moduler RESET: start working.
Moduler DIAGNOSTIC: start working.
Moduler BAKNRESTORE: start working.
Moduler HTTP-FIRMWARE: start working.
Moduler IGMP: start working.
Moduler ANTI-SNIFFER: start working.
Moduler SNTPC: start working.


eduedu530 发表于 2016-3-7 19:14

小康子 发表于 2015-12-27 15:23
帅哥，我的路由器和你这个一样，能通过这种方法找到管理路由的用户名和密码嘛，目的是想找到宽带账号

晕，问一下电信就OK了

eduedu530 发表于 2014-6-6 08:41

怎么只看不回复啊，自己坐。{:5_238:}

血洗刀锋 发表于 2014-6-6 09:01

没标注只有自己用万能表测。。。

eduedu530 发表于 2014-6-6 09:13

血洗刀锋 发表于 2014-6-6 09:01 static/image/common/back.gif
没标注只有自己用万能表测。。。

图片不是标注了吗？从左到右：VCC 没接线柱、GNDTX    RX   
并且，短接的两个电阻，分别跟TX (R50)\（R32）RX 相连接

Lerser 发表于 2014-6-8 09:31

小手一抖，金币到手！！！！

冷焰心 发表于 2014-6-23 11:26

楼主，图片上RX针-R32-R78左端点要连在一起的对么？
TX针-R50连一起（R50不与R23做端点短接）对么？
这个折腾我几天了，一直没成功

eduedu530 发表于 2014-7-8 14:43

本帖最后由 eduedu530 于 2014-7-8 14:47 编辑

冷焰心 发表于 2014-6-23 11:26 http://www.anywlan.com/static/image/common/back.gif
楼主，图片上RX针-R32-R78左端点要连在一起的对么？
TX针-R50连一起（R50不与R23做端点短接）对么？
这个 ...

wr842 v4.1 ttl 接线 步骤：
1、短接R50，R32 两个电阻。
2、J3 四个接口（LED指示灯正对自己） 从左到右分

如果不行,你对调一下(TTL上 的RX TX).你只需要短接R50 ,R32 这两个电阻就可以了.不短接,就直接接到电阻(R78,R32)上啊.R78,R32分别通过R32,R50 (串联)到---RX .TX上

xqxcn 发表于 2014-7-8 22:52

看似接线没错误呀，你要做什么？

fanglei727 发表于 2014-7-19 23:02

兄弟,这么接线具体有什么用啊.这个路由器能刷其它固件么

dhtdwj 发表于 2014-9-12 10:53

:hug::hug::hug:

通化呈翔 发表于 2014-9-24 22:39

在网刷省时省力，何必要TTL刷呢

shijiyingxia 发表于 2014-11-25 17:15

很不错啊，我也想刷刷
页: [1] 2
查看完整版本: wr842 v4.1 ttl 接线图-测试通过。