高手来看看这货怎么玩
这是ttl用SecureCRT的信息U-Boot 1.1.4 (Jul2 2012 - 08:49:23)
U-boot DB120
DRAM:128 MB
id read 0x100000ff
flash size 4MB, sector count = 64
Flash:4 MB
Using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
waspreset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: ba:be:fa:ce:08:41
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.36 (bowang@bowang-virtual-machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41336) ) #1 Wed Jun 25 22:45:11 CST 2014
[ 0.000000] bootconsole enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0:
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 32512
[ 0.000000] Kernel command line:board=TL-WDR3500 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126248k/131072k available (2231k kernel code, 4824k reserved, 594k data, 244k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is TP-LINK TL-WDR3500
[ 0.090000] ar724x-pci ar724x-pci: PCIe link is down
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.510000] bio: create slab <bio-0> at 0
[ 0.510000] PCI host bridge to bus 0000:00
[ 0.520000] pci_bus 0000:00: root bus resource
[ 0.520000] pci_bus 0000:00: root bus resource
[ 0.530000] pci_bus 0000:00: No busn resource found for root bus, will use
[ 0.530000] Switching to clocksource MIPS
[ 0.540000] NET: Registered protocol family 2
[ 0.540000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.550000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.560000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.560000] TCP: reno registered
[ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] NET: Registered protocol family 1
[ 0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.610000] msgmni has been set to 246
[ 0.620000] io scheduler noop registered
[ 0.620000] io scheduler deadline registered (default)
[ 0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.660000] console enabled, bootconsole disabled
[ 0.660000] console enabled, bootconsole disabled
[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.680000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.680000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.690000] 5 tp-link partitions found on MTD device spi0.0
[ 0.700000] Creating 5 MTD partitions on "spi0.0":
[ 0.700000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.710000] 0x000000020000-0x00000011df68 : "kernel"
[ 0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.730000] 0x00000011df68-0x000000ff0000 : "rootfs"
[ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.740000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.750000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.760000] 0x000000530000-0x000000ff0000 : "rootfs_data"
[ 0.760000] 0x000000ff0000-0x000001000000 : "art"
[ 0.770000] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.790000] libphy: ag71xx_mdio: probed
[ 1.350000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.380000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.930000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04
[ 2.940000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.950000] TCP: cubic registered
[ 2.950000] NET: Registered protocol family 17
[ 2.960000] 8021q: 802.1Q VLAN Support v1.8
[ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.980000] Freeing unused kernel memory: 244K (80323000 - 80360000)
procd: Console is alive
procd: - watchdog -
[ 5.320000] usbcore: registered new interface driver usbfs
[ 5.330000] usbcore: registered new interface driver hub
[ 5.340000] usbcore: registered new device driver usb
[ 5.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.350000] ehci-platform: EHCI generic platform driver
[ 5.360000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.360000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.370000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.400000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.400000] hub 1-0:1.0: USB hub found
[ 5.410000] hub 1-0:1.0: 1 port detected
[ 5.410000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the key and hit to enter failsafe mode
Press the , , or key and hit to select the debug level
[ 8.090000] eth0: link up (1000Mbps/Full duplex)
kmod: ran 1 iterations
[ 9.640000] jffs2: notice: (319) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 18 of xref (0 dead, 0 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 9.730000] jffs2: notice: (316) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 18 of xref (0 dead, 0 orphan) found.
switching to overlay
[ 9.770000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 11.510000] NET: Registered protocol family 10
[ 11.520000] sit: IPv6 over IPv4 tunneling driver
[ 11.550000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[ 11.570000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.630000] u32 classifier
[ 11.630000] input device check on
[ 11.630000] Actions configured
[ 11.640000] Mirror/redirect action on
[ 11.660000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 11.670000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 11.680000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.820000] xt_time: kernel timezone is -0000
[ 11.880000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.880000] cfg80211: World regulatory domain updated:
[ 11.890000] cfg80211:DFS Master region: unset
[ 11.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.900000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.910000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.920000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.930000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.940000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.990000] PPP generic driver version 2.4.2
[ 11.990000] NET: Registered protocol family 24
[ 12.090000] cfg80211: Calling CRDA for country: US
[ 12.100000] cfg80211: Regulatory domain changed to country: US
[ 12.100000] cfg80211:DFS Master region: FCC
[ 12.110000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.120000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.120000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 12.130000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 12.140000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.150000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 12.160000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 21.460000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.460000] device eth0 entered promiscuous mode
[ 21.470000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 21.480000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 21.520000] IPv6: ADDRCONF(NETDEV_UP): br-wwan: link is not ready
[ 22.570000] eth0: link up (1000Mbps/Full duplex)
[ 22.570000] br-lan: port 1(eth0) entered forwarding state
[ 22.580000] br-lan: port 1(eth0) entered forwarding state
[ 22.580000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.620000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 23.780000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 23.790000] device wlan0-1 entered promiscuous mode
[ 24.020000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.580000] br-lan: port 1(eth0) entered forwarding state
procd: - init complete -
[ 34.980000] device mon0 entered promiscuous mode
如果我分析的没错，是ar9344,flash，4m，内存128.
这货原机系统固件op的营销固件。不知道管理密码，开机默认没无线，复位不好使。求高手大神指教怎么玩。ttl刷机怎么备份原系统？
刷5.8G UBNT qk796796 发表于 2015-6-17 14:10
刷5.8G UBNT
不带这么玩的！ 自己顶起123456789
页:
[1]