双频9344+8327+9382求大神解疑惑
双频9344+8327+9382求大神解疑惑是这样的路由器，鬼子货
卖家刷的wndr4300V1 openwrt
问题是功率20想刷明月的，可升级后就进重启中，有几秒的时间可以打开WEB页，但不停还是重启。希望大神能帮忙看看
买回正常启动编程器固件 http://pan.baidu.com/s/1nuj2XCl
u-boot停下httpd后路由器和电脑始终不通，所以不死没有办法用
正常启动TTL信息
U-Boot 1.1.4 (Apr 21 2014 - 17:18:41)
DB120 (AR9344 - Wasp 1.1) U-Boot
DRAM:128 MB
Flash: Macronix MX25L640 (8 MB)
Using default environment
Clocks: CPU:560MHz, DDR:450MHz, AHB:225MHz
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x9f01fc00
WASP----> S17 PHY *
GMAC: cfg1 0x7 cfg2 0x7114
eth0: 10:66:82:81:57:2f
athrs17_reg_init: complete
eth0 up
eth0
Hit any key to stop autoboot:0
## Booting image at 9f020000 ...
Image Name: Unknown board (43000001)
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 8125952 Bytes =7.7 MB
Load Address: 80060000
Entry Point:80060000
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.36 (bian@lijie) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r40774) ) #2 Mon Jun 2 15:47:41 CST 2014
[ 0.000000] bootconsole enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 1
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0:
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 32512
[ 0.000000] Kernel command line:board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126248k/131072k available (2217k kernel code, 4824k reserved, 591k data, 260k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource
[ 0.320000] pci_bus 0000:00: root bus resource
[ 0.330000] pci_bus 0000:00: No busn resource found for root bus, will use
[ 0.330000] pci 0000:00:00.0: invalid calibration data
[ 0.340000] pci 0000:00:00.0: BAR 0: assigned
[ 0.340000] pci 0000:00:00.0: BAR 6: assigned
[ 0.350000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.350000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.370000] TCP: reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 246
[ 0.430000] io scheduler noop registered
[ 0.430000] io scheduler deadline registered (default)
[ 0.430000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.460000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.470000] console enabled, bootconsole disabled
[ 0.470000] console enabled, bootconsole disabled
[ 0.480000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.490000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.490000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.500000] 5 tp-link partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.510000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.520000] 0x000000020000-0x00000011cac0 : "kernel"
[ 0.520000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] 0x00000011cac0-0x0000007f0000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.560000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.560000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.570000] 0x000000580000-0x0000007f0000 : "rootfs_data"
[ 0.570000] 0x0000007f0000-0x000000800000 : "art"
[ 0.580000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.620000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.830000] libphy: ag71xx_mdio: probed
[ 2.390000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00
[ 2.400000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.410000] TCP: cubic registered
[ 2.410000] NET: Registered protocol family 17
[ 2.410000] 8021q: 802.1Q VLAN Support v1.8
[ 2.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.430000] Freeing unused kernel memory: 260K (8031f000 - 80360000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
Press the key and hit to enter failsafe mode
Press the , , or key and hit to select the debug level
[ 7.010000] usbcore: registered new interface driver usbfs
[ 7.020000] usbcore: registered new interface driver hub
[ 7.020000] usbcore: registered new device driver usb
[ 7.070000] SCSI subsystem initialized
[ 7.080000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.090000] ehci-platform: EHCI generic platform driver
[ 7.090000] ehci-platform ehci-platform: EHCI Host Controller
[ 7.100000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 7.110000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 7.130000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 7.130000] hub 1-0:1.0: USB hub found
[ 7.140000] hub 1-0:1.0: 1 port detected
[ 7.140000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.150000] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.170000] usbcore: registered new interface driver usb-storage
[ 7.180000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 7.490000] eth0: link up (1000Mbps/Full duplex)
[ 9.340000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
kmod: ran 1 iterations
kmod: 1 module could not be probed
kmod: - gpio_keys_polled - 0
[ 9.530000] jffs2: notice: (381) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 5 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
[ 9.590000] jffs2: notice: (376) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 5 orphan) found.
switching to jffs2
[ 9.620000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 12.090000] NET: Registered protocol family 10
[ 12.110000] NTFS driver 2.1.30 .
[ 12.130000] gre: GRE over IPv4 demultiplexor driver
[ 12.130000] ip_gre: GRE over IPv4 tunneling driver
[ 12.160000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[ 12.170000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.330000] ath_hal: module license 'Proprietary' taints kernel.
[ 12.330000] Disabling lock debugging due to kernel taint
[ 12.370000] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR)
[ 12.410000] ath_pci: trunk
[ 12.410000] wlan: trunk
[ 12.410000] wlan: mac acl policy registered
[ 12.410000] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
[ 12.420000] ath_rate_minstrel: look around rate set to 10%
[ 12.430000] ath_rate_minstrel: EWMA rolloff level set to 75%
[ 12.430000] ath_rate_minstrel: max segment size in the mrr set to 6000 us
[ 12.480000] fuse init (API version 7.22)
[ 12.490000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 12.500000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 12.510000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 12.520000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 12.540000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.570000] usbcore: registered new interface driver ums-alauda
[ 12.580000] usbcore: registered new interface driver ums-cypress
[ 12.590000] usbcore: registered new interface driver ums-datafab
[ 12.600000] usbcore: registered new interface driver ums-freecom
[ 12.610000] usbcore: registered new interface driver ums-isd200
[ 12.620000] usbcore: registered new interface driver ums-jumpshot
[ 12.630000] usbcore: registered new interface driver ums-karma
[ 12.630000] usbcore: registered new interface driver ums-sddr09
[ 12.640000] usbcore: registered new interface driver ums-sddr55
[ 12.650000] usbcore: registered new interface driver ums-usbat
[ 12.660000] usbcore: registered new interface driver usblp
[ 12.690000] xt_time: kernel timezone is -0000
[ 12.720000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.720000] cfg80211: World regulatory domain updated:
[ 12.730000] cfg80211:DFS Master region: unset
[ 12.730000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.740000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.750000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.760000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.770000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.770000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.780000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 12.790000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 12.810000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 12.880000] PPP generic driver version 2.4.2
[ 12.880000] NET: Registered protocol family 24
[ 12.920000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 12.930000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 12.940000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 12.950000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 13.000000] cfg80211: Calling CRDA for country: JP
[ 13.000000] cfg80211: Regulatory domain changed to country: JP
[ 13.010000] cfg80211:DFS Master region: JP
[ 13.010000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.020000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.030000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.040000] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
[ 13.050000] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
[ 13.060000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.070000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
[ 13.070000] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 13.080000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 13.090000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 13.140000] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40
[ 13.160000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 13.180000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 13.180000] Error: Driver 'gpio-keys' is already registered, aborting...
[ 13.200000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 21.880000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.880000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 21.910000] device eth0.1 entered promiscuous mode
[ 21.910000] device eth0 entered promiscuous mode
[ 21.940000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 21.980000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 23.830000] eth0: link up (1000Mbps/Full duplex)
[ 23.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.930000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.930000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.940000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 23.940000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 23.950000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
procd: - init complete -
[ 24.990000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 25.020000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.030000] device wlan1 entered promiscuous mode
[ 25.040000] br-lan: port 2(wlan1) entered forwarding state
[ 25.040000] br-lan: port 2(wlan1) entered forwarding state
[ 25.050000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 25.080000] device wlan0 entered promiscuous mode
[ 25.080000] br-lan: port 3(wlan0) entered forwarding state
[ 25.090000] br-lan: port 3(wlan0) entered forwarding state
[ 25.120000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 25.930000] br-lan: port 1(eth0.1) entered forwarding state
[ 27.040000] br-lan: port 2(wlan1) entered forwarding state
[ 27.090000] br-lan: port 3(wlan0) entered forwarding state
niejun643586 发表于 2016-1-4 09:43
https://item.taobao.com/item.htm?spm=a230r.1.14.171.6eDkN8&id=40755288565&ns=1&abbucket=5#detail
刷其他固件就不停重启，得刷他们的固件，而他们的固件功率才20 如果只是不停重启，可能是复位按钮的定义问题 小茅 发表于 2016-1-4 00:16
如果只是不停重启，可能是复位按钮的定义问题
知道怎么修改吗 看起来是好东西了 lkylky 发表于 2016-1-4 08:09
在什么地方买的？？？？？？？？？？？？给个链接看看
https://item.taobao.com/item.htm?spm=a230r.1.14.171.6eDkN8&id=40755288565&ns=1&abbucket=5#detail 小茅 发表于 2016-1-4 00:16
如果只是不停重启，可能是复位按钮的定义问题
速度够快还能能进不死的
要是最新的那个不死就好了直接软件进入 下载最新的berrd以极快的速度选择刷新 然后用软件进入berrd再刷复位键相同的不死 130买这东西 ，直接买电信级ap 改usb和lan就行了 还带外壳 价格不高于这个 1000mw功放你懂得 :D终于知道是什么主板了hp-600n 是这个拆机主板
不知那位大神能帮忙转点固件 zhangweizhen666 发表于 2016-1-4 11:57
130买这东西 ，直接买电信级ap 改usb和lan就行了 还带外壳 价格不高于这个 1000mw功放你懂得
能详细介绍下吗？特别是改usb和lan，有无具体型号推荐，谢谢！
页:
[1]
2