请高手帮看下我的路由TTL信息，接下来如何刷机？
本帖最后由 joyoung 于 2016-3-31 11:22 编辑COMBA定制营销路由AP2400-I，AR9341CPU,16M/128M，带usb和tf卡槽，应该是定制的Openwrt系统，web登陆路由里面能改的功能非常少，打算刷成标准openwrt使用。
按照网上的一些教程，连接TTL线，进入putty，printenv看下ip，改了电脑ip准备tftp
执行命令 tftpboot 0x80000000 openwrt-ar71xx-generic-tl-wr841n-v8-squashfs-factory.bin成功后
没敢下手执行erase 0x9f020000+0x3c0000 担心网上的闪存地址与我的路由不符，导致故障。
请高手帮看下ttl信息，接下来改如何刷机？我应该先刷ar9341的breed吗？或者，这种情况下，我刷openwrt-ar71xx-generic-tl-wr841n-v8-squashfs-sysupgrade.bin是不是就可以？可不用改mac和art？
或者有什么办法绕开路由的user级web管理界面，让我登录到admin。
我想关闭它第二个wifi信号（营销认证后免费登陆使用，used管理界面且无法关闭），增加usb共享，下载和dlna功能
========================================
U-Boot 1.1.4.21-MULT (May 19 2015 - 10:10:37)
U-boot AP123
DRAM:***comba***: watchdog on!
sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf
Setting 0xb8116290 to 0x60c02d0f
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 275k for U-Boot at: 87fb8000
Reserving 192k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb8000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0xxxxxxxxx
Fetching MAC Address from 0xxxxxxxxx
waspreset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: 00:27:1d:22:3e:dd
s27 reg init
unit0:s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0x7 cfg2 0x7214
eth1: 00:27:1d:22:3e:de
unit1:s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :50
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
***comba***: watchdog off!
Hit any key to stop autoboot:0
u-boot> printenv
bootargs=board=BXU2000n-2-A1 console=ttyS0,115200 root=31:03 mtdparts=spi0.0:256k(uboot)ro,64k(ubtenv)ro,1408k(kernel),6528k(rootfs),1408k(kernel-b)ro,6528k(rootfs-b)ro,64k(cfg),64k(pinfo),64k(art)ro,7936k@0x50000(firmware) rootfstype=squashfs noinitrd
bootcmd=bootm 0x9f050000
bootdelay=4
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.197.2
serverip=192.168.197.241
dir=
bc=ap123
lu=tftp 0x80060000 u-boot_${bc}.bin&&erase 0x9f000000 +$filesize;cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}${bc}-jffs2&&erase 0x9f160000 +$filesize;cp.b $fileaddr 0x9f160000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux_${bc}.lzma.uImage&&erase 0x9f050000 +$filesize;cp.b $fileaddr 0x9f050000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
bootargsfw1=console=ttyS0,115200 root=31:04 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(boot),64k(env),128k(swap),1024k(k1),5120k(r1),1472k(mnt1),1024k(k2),5120k(r2),1472k(mnt2),576k(rev),64k(cfg),64k(eeprom)
bootargsfw2=console=ttyS0,115200 root=31:07 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(boot),64k(env),128k(swap),1024k(k1),5120k(r1),1472k(mnt1),1024k(k2),5120k(r2),1472k(mnt2),576k(rev),64k(cfg),64k(eeprom)
bootcmdfw1=bootm 0x9f070000
bootcmdfw2=bootm 0x9f7e0000
Environment size: 1280/65532 bytes
u-boot>
BusyBox v1.22.1 (2015-01-21 18:37:02 HKT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.||||.----.||_
| - ||_|-__| |||||| _|| _|
|_______|| __|_____|__|__||________||__||____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r43889)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
apcomba@COMBA:/# [ 70.920000] wifidog uses obsolete (PF_INET,SOCK_PACKET)
[ 71.160000] device br-lan entered promiscuous mode
procd: - init complete -
[ 75.680000] MAXNET DPI interface Loaded
apcomba@COMBA:/#
----------------------------------------分割线--------------------------------------------------------------
U-Boot 1.1.4.21-MULT (May 19 2015 - 10:10:37)
U-boot AP123
DRAM:***comba***: watchdog on!
sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf
Setting 0xb8116290 to 0x60c02d0f
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 275k for U-Boot at: 87fb8000
Reserving 192k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb8000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x80000000
Fetching MAC Address from 0x80000000
waspreset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: 00:27:1d:22:3e:dd
s27 reg init
unit0:s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0x7 cfg2 0x7214
eth1: 00:27:1d:22:3e:de
unit1:s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
***comba***: watchdog off!
Hit any key to stop autoboot:0
First 0xfe last 0xfe sector size 0x10000
254
write addr: 9ffe0000
****count_number=0x1***
****load_addr=0x9f050000***
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2015-07-16 6:54:21 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1129611 Bytes =1.1 MB
Load Address: 80060000
Entry Point:80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (root@bianqinghong-ubutu1310) (gcc version
4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43889) ) #140 Thu Jul 16 14:54:05 HKT 2015
[ 0.000000] bootconsole enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 1
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000]memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0:
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages:
32512
[ 0.000000] Kernel command line:board=BXU2000n-2-A1 console=ttyS0,115200
root=31:03 mtdparts=spi0.0:256k(uboot)ro,64k(ubtenv)ro,1408k(kernel),6528k
(rootfs),1408k(kernel-b)ro,6528k(rootfs-b)ro,64k(cfg),64k(pinfo),64k(art)
ro,7936k@0x50000(firmware) rootfstype=squashfs noinitrd mem=128M
rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126056k/131072k available (2256k kernel code, 5016k reserved,
730k data, 276k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is BHU BXU2000n-2 rev. A1
[ 0.100000] BQH::Read MAC form Product info::00271d223eddBQH::Read MAC form
Product info::00271d223edd
[ 0.520000] bio: create slab <bio-0> at 0
[ 0.530000] Switching to clocksource MIPS
[ 0.540000] NET: Registered protocol family 2
[ 0.540000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.550000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.550000] TCP: reno registered
[ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.570000] NET: Registered protocol family 1
[ 0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.590000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY)
(c) 2001-2006 Red Hat, Inc.
[ 0.610000] msgmni has been set to 246
[ 0.610000] io scheduler noop registered
[ 0.610000] io scheduler deadline registered (default)
[ 0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.650000] console enabled, bootconsole disabled
[ 0.650000] console enabled, bootconsole disabled
[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.670000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.680000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.690000] 10 cmdlinepart partitions found on MTD device spi0.0
[ 0.690000] Creating 10 MTD partitions on "spi0.0":
[ 0.700000] 0x000000000000-0x000000040000 : "uboot"
[ 0.700000] 0x000000040000-0x000000050000 : "ubtenv"
[ 0.710000] 0x000000050000-0x0000001b0000 : "kernel"
[ 0.720000] 0x0000001b0000-0x000000810000 : "rootfs"
[ 0.720000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.730000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.740000] 0x000000700000-0x000000810000 : "rootfs_data"
[ 0.740000] 0x000000810000-0x000000970000 : "kernel-b"
[ 0.750000] 0x000000970000-0x000000fd0000 : "rootfs-b"
[ 0.760000] 0x000000fd0000-0x000000fe0000 : "cfg"
[ 0.760000] 0x000000fe0000-0x000000ff0000 : "pinfo"
[ 0.770000] 0x000000ff0000-0x000001000000 : "art"
[ 0.780000] 0x000000050000-0x000000810000 : "firmware"
[ 0.800000] libphy: ag71xx_mdio: probed
[ 1.360000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042,
driver=Generic PHY]
[ 1.370000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.920000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.960000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.970000] TCP: cubic registered
[ 2.970000] NET: Registered protocol family 17
[ 2.970000] 8021q: 802.1Q VLAN Support v1.8
[ 2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.990000] Freeing unused kernel memory: 276K (8034b000 - 80390000)
procd: Console is alive
procd: - watchdog -
[ 6.070000] usbcore: registered new interface driver usbfs
[ 6.070000] usbcore: registered new interface driver hub
[ 6.080000] usbcore: registered new device driver usb
[ 6.130000] SCSI subsystem initialized
[ 6.140000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.150000] ehci-platform: EHCI generic platform driver
[ 6.150000] ehci-platform ehci-platform: EHCI Host Controller
[ 6.160000] ehci-platform ehci-platform: new USB bus registered, assigned bus
number 1
[ 6.170000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.200000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.200000] hub 1-0:1.0: USB hub found
[ 6.210000] hub 1-0:1.0: 1 port detected
[ 6.210000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.220000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 6.640000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.810000] hub 1-1:1.0: USB hub found
write flash data[ 6.820000] hub 1-1:1.0: 4 ports detected
read to /tmp/sysinfo/model
write flash data read to /tmp/sysinfo/comba_hw_version
write flash data read to /tmp/sysinfo/comba_product_sn
Press the key and hit to enter failsafe mode
Press the , , or key and hit to select the debug level
[ 7.100000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[ 7.220000] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 7.230000] usb-storage 1-1.1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 7.240000] scsi0 : usb-storage 1-1.1:1.0
[ 8.240000] scsi 0:0:0:0: Direct-Access GenericSTORAGE DEVICE 9451 PQ: 0
ANSI: 0
[ 8.250000] sd 0:0:0:0: Attached SCSI removable disk
kmod: ran 1 iterations
[ 10.680000] jffs2: notice: (360) jffs2_build_xattr_subsystem: complete building
xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 79 of xref (0 dead, 63
orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 10.750000] jffs2: notice: (357) jffs2_build_xattr_subsystem: complete building
xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 79 of xref (0 dead, 63
orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 12.800000] NET: Registered protocol family 10
[ 12.820000] NTFS driver 2.1.30 .
[ 12.860000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
[ 12.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.940000] u32 classifier
[ 12.950000] input device check on
[ 12.950000] Actions configured
[ 12.960000] Mirror/redirect action on
[ 12.980000] Failed to load ipt action
[ 13.060000] arp_tables: (C) 2002 David S. Miller
[ 13.070000] Loading modules backported from Linux version master-2014-05-22-0-
gf2032ea
[ 13.080000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 13.100000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.170000] Netfilter messages via NETLINK v0.30.
[ 13.180000] usbcore: registered new interface driver ums-alauda
[ 13.210000] usbcore: registered new interface driver ums-cypress
[ 13.230000] usbcore: registered new interface driver ums-datafab
[ 13.230000] usbcore: registered new interface driver ums-freecom
[ 13.250000] usbcore: registered new interface driver ums-isd200
[ 13.250000] usbcore: registered new interface driver ums-jumpshot
[ 13.260000] usbcore: registered new interface driver ums-karma
[ 13.270000] usbcore: registered new interface driver ums-sddr09
[ 13.280000] usbcore: registered new interface driver ums-sddr55
[ 13.290000] usbcore: registered new interface driver ums-usbat
[ 13.360000] xt_time: kernel timezone is -0000
[ 13.400000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.400000] cfg80211: World regulatory domain updated:
[ 13.410000] cfg80211:DFS Master region: unset
[ 13.410000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
[ 13.420000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm),
(N/A)
[ 13.430000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm),
(N/A)
[ 13.440000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm),
(N/A)
[ 13.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000
mBm), (N/A)
[ 13.450000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000
mBm), (0 s)
[ 13.460000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000
mBm), (0 s)
[ 13.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm),
(N/A)
[ 13.480000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
mBm), (N/A)
[ 13.570000] ctnetlink v0.93: registering with nfnetlink.
[ 13.580000] PPP generic driver version 2.4.2
[ 13.580000] NET: Registered protocol family 24
[ 13.670000] cfg80211: Calling CRDA for country: CN
[ 13.680000] cfg80211: Regulatory domain changed to country: CN
[ 13.680000] cfg80211:DFS Master region: FCC
[ 13.690000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
[ 13.700000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2600 mBm),
(N/A)
[ 13.700000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2300 mBm),
(N/A)
[ 13.710000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm),
(0 s)
[ 13.720000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm),
(N/A)
[ 13.730000] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800
mBm), (N/A)
[ 13.740000] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400
mBm), (N/A)
[ 13.750000] cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800
mBm), (N/A)
[ 13.750000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 18.570000] [**ar7240sw_setup_port**]port:0(tag:0)
[ 18.570000] [**ar7240sw_setup_port**]vlan:1,portmask:30
[ 18.580000] [**ar7240sw_setup_port**]port:1(tag:0)
[ 18.580000] [**ar7240sw_setup_port**]vlan:1,portmask:29
[ 18.590000] [**ar7240sw_setup_port**]port:2(tag:0)
[ 18.590000] [**ar7240sw_setup_port**]vlan:1,portmask:27
[ 18.600000] [**ar7240sw_setup_port**]port:3(tag:0)
[ 18.600000] [**ar7240sw_setup_port**]vlan:1,portmask:23
[ 18.610000] [**ar7240sw_setup_port**]port:4(tag:0)
[ 18.610000] [**ar7240sw_setup_port**]vlan:1,portmask:15
[ 22.850000] [**ar7240sw_setup_port**]port:0(tag:0)
[ 22.850000] [**ar7240sw_setup_port**]vlan:1,portmask:30
[ 22.860000] [**ar7240sw_setup_port**]port:1(tag:0)
[ 22.860000] [**ar7240sw_setup_port**]vlan:1,portmask:29
[ 22.870000] [**ar7240sw_setup_port**]port:2(tag:0)
[ 22.870000] [**ar7240sw_setup_port**]vlan:1,portmask:27
[ 22.880000] [**ar7240sw_setup_port**]port:3(tag:0)
[ 22.880000] [**ar7240sw_setup_port**]vlan:1,portmask:23
[ 22.890000] [**ar7240sw_setup_port**]port:4(tag:0)
[ 22.890000] [**ar7240sw_setup_port**]vlan:1,portmask:15
[ 22.900000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 22.900000] device eth1 entered promiscuous mode
[ 22.910000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 22.930000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.960000] IPv6: ADDRCONF(NETDEV_UP): br-pt: link is not ready
[ 23.570000] eth1: link up (1000Mbps/Full duplex)
[ 23.570000] br-lan: port 1(eth1) entered forwarding state
[ 23.580000] br-lan: port 1(eth1) entered forwarding state
[ 23.580000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 23.610000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.580000] br-lan: port 1(eth1) entered forwarding state
[ 25.630000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.640000] device wlan0 entered promiscuous mode
[ 27.230000] br-lan: port 2(wlan0) entered forwarding state
[ 27.240000] br-lan: port 2(wlan0) entered forwarding state
[ 27.240000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 27.280000] device wlan0-1 entered promiscuous mode
[ 27.290000] br-pt: port 1(wlan0-1) entered forwarding state
[ 27.290000] br-pt: port 1(wlan0-1) entered forwarding state
[ 27.300000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 27.310000] IPv6: ADDRCONF(NETDEV_CHANGE): br-pt: link becomes ready
[ 27.330000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 29.240000] br-lan: port 2(wlan0) entered forwarding state
[ 29.290000] br-pt: port 1(wlan0-1) entered forwarding state
[ 70.940000] wifidog uses obsolete (PF_INET,SOCK_PACKET)
[ 71.290000] device br-lan entered promiscuous mode
procd: - init complete -
[ 75.810000] MAXNET DPI interface Loaded
memshr init OK
this is the kernel dpi loaded by maxnet
这种情况下，我刷openwrt-ar71xx-generic-tl-wr841n-v8-squashfs-sysupgrade.bin是不是就可以？可以不用改mac和担心art？ 或者有什么办法绕开路由的user级web管理界面，让我登录到admin。
我想关闭它第二个wifi信号（营销认证后免费登陆使用），增加usb共享支持和dlna功能
页:
[1]