liangabcd2205 发表于 2020-2-24 01:47

迈外迪刷机遇到无法选择boot问题

完全不给选择的机会啊，狂按2没反应求大神指点下

U-Boot 1.1.3 (Feb2 2015 - 15:31:41)

Board: Ralink APSoC DRAM:128 MB
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
reg = 0xc0030000
reg = 0xc0030000
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Wiwide UBoot Version: 1.0.3
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: 16 MBytes NOR Flash
Date:Feb2 2015Time:15:31:41
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
raspi_read: from:50000 len:40
raspi_read: from:850000 len:40

=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> raspi_read: from:50040 len:696484
OK
Image2 Data Checksum --> raspi_read: from:850040 len:696484
OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 1

Image1: OK Image2: OK

=================================================
raspi_read: from:40028 len:6


Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.


3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   OpenWrt Linux-3.10.14-p112871
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6907012 Bytes =6.6 MB
   Load Address: 80000000
   Entry Point:80000000
raspi_read: from:50040 len:696484
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

鎬榾鄻啒鴺ff橒~嗻~fx鴨鴨鴨鎬榾鎬榾f

tvro999 发表于 2020-2-24 16:53

拆了刷机省事省心

nnsat 发表于 2020-2-25 09:34

不妨换个终端试一下，刷机硬件软件都换

huruiqi 发表于 2020-3-27 10:05

直接拆闪存，编程器刷breed，我这几天成功刷了七八台
7620的固件都能刷，老毛子的潘多拉固件比较好用

htsbhxx 发表于 2022-5-28 17:37

这玩意到底要怎么刷啊

htsbhxx 发表于 2022-5-28 17:38

我弄了半天都没办法

htsbhxx 发表于 2022-5-28 17:38

有大神能出个教程么

htsbhxx 发表于 2022-5-28 17:39

:Q:Q:Q:Q:Q:Q:Q:Q:Q

htsbhxx 发表于 2022-5-28 17:39

:Q:Q:Q:Q:Q:Q:Q:Q:Q:Q

htsbhxx 发表于 2022-5-28 17:40

:Q:Q:Q:Q:Q:Q
页: [1]
查看完整版本: 迈外迪刷机遇到无法选择boot问题