百米生活2刷机刷固件重启后自动恢复
本帖最后由 pzq130 于 2022-6-17 13:02 编辑准备在鱼塘边上安装一监控，想到用定向接收wifi信号的方式来架网，在x鱼上淘了个百米生活2的路由器，原以为很简单可以WEB直刷波讯固件，可偏偏遇到了一不能直刷的，于是在网上找啊找啊，结果忙活了两天，工具、软件装了一大堆，结果还是没结果，不管用直刷，还是用TTL刷进去，启动后还是原来的样子。熬夜不少，结果还是不行，特在此求助大神，看有没有什么办法解决！
拆机主板：芯片为AR9341 AL1A的
系统登录界面：软件版本为100MSHBHU2S_R_2.36
UBOOT界面，无解锁项：
TLL线跑码，可见有上传项，可是上传了不同的固件，都是重启回到自身系统。
如果中断跑，最后要让输入用户名和密码，试过不同的方式，没一个正确。
:Q:Q:Q下的各种软件，各种固件…………
以上就是这样，在x鱼上已确认收货，无法退回，有请各位大神帮解决一下，不然就费了。
自己有线刷，无编程器
只要可以中继WIFI，并能设置密码就行。
只有42个币了，解决了一并赠送！
感谢！！！
以下是跑码数据：
U-Boot 1.1.4 (Apr3 2013 - 14:18:20)
U-boot BXO2000n-2S
DRAM:
sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf
Setting 0xb8116290 to 0x38702d0f
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 240k for U-Boot at: 83fc0000
Reserving 192k for malloc() at: 83f90000
Reserving 44 Bytes for Board Info at: 83f8ffd4
Reserving 36 Bytes for Global Data at: 83f8ffb0
Reserving 128k for boot params() at: 83f6ffb0
Stack Pointer at: 83f6ff98
Now running in RAM - U-Boot at: 83fc0000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:8 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
_______ _ _ _
|_____] |_____| | |
|_____] | | |_____| Networks Co'Ltd Inc.
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
waspreset mask:c03300
WASP ----> S27 PHY
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Hit any key to stop autoboot:0
## Booting image at 9f690000 ...
Image Name: MIPS OpenWrt Linux-3.10.36
Created: 2016-05-23 8:51:38 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1037418 Bytes = 1013.1 kB
Load Address: 80060000
Entry Point:80060000
Verifying Checksum at 0x9f690040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
[ 0.000000] Linux version 3.10.36 (controller@localhost.localdomain) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 unknown) ) #14 Mon May 23 16:51:29 CST 2016
[ 0.000000] bootconsole enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 1
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0:
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16256
[ 0.000000] Kernel command line:board=BXO2000n-2S-A1 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),6400k(rootfs),1280k(kernel),64k(cfg),64k(oem),64k(art)ro,7680k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61272k/65536k available (2226k kernel code, 4264k reserved, 590k data, 252k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is BHU BXO2000n-2S rev. A1
[ 0.510000] bio: create slab <bio-0> at 0
[ 0.510000] Switching to clocksource MIPS
[ 0.520000] NET: Registered protocol family 2
[ 0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.540000] TCP: Hash tables configured (established 512 bind 512)
[ 0.540000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.560000] NET: Registered protocol family 1
[ 0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.580000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.590000] msgmni has been set to 119
[ 0.600000] io scheduler noop registered
[ 0.600000] io scheduler deadline registered (default)
[ 0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.640000] console enabled, bootconsole disabled
[ 0.640000] console enabled, bootconsole disabled
[ 0.650000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.660000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.670000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.670000] 8 cmdlinepart partitions found on MTD device spi0.0
[ 0.680000] Creating 8 MTD partitions on "spi0.0":
[ 0.680000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.690000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.700000] 0x000000050000-0x000000690000 : "rootfs"
[ 0.700000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.710000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.720000] 0x000000360000-0x000000690000 : "rootfs_data"
[ 0.720000] 0x000000690000-0x0000007d0000 : "kernel"
[ 0.730000] 0x0000007d0000-0x0000007e0000 : "cfg"
[ 0.740000] 0x0000007e0000-0x0000007f0000 : "oem"
[ 0.740000] 0x0000007f0000-0x000000800000 : "art"
[ 0.750000] 0x000000050000-0x0000007d0000 : "firmware"
[ 0.770000] libphy: ag71xx_mdio: probed
[ 1.330000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04
[ 1.340000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.900000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.930000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.940000] TCP: cubic registered
[ 2.940000] NET: Registered protocol family 17
[ 2.950000] 8021q: 802.1Q VLAN Support v1.8
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.960000] Freeing unused kernel memory: 252K (80321000 - 80360000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
jffs2 is ready
[ 6.160000] jffs2: notice: (274) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 17 of xref (0 dead, 0 orphan) found.
switching to jffs2
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 8.430000] u32 classifier
[ 8.430000] input device check on
[ 8.430000] Actions configured
[ 8.450000] Mirror/redirect action on
[ 8.470000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[ 8.510000] Failed to load ipt action
[ 8.550000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 8.560000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 8.590000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.720000] xt_time: kernel timezone is -0000
[ 8.780000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.800000] cfg80211: World regulatory domain updated:
[ 8.800000] cfg80211:DFS Master region: unset
[ 8.810000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.820000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.820000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.830000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.850000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.860000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 8.940000] PPP generic driver version 2.4.2
[ 8.960000] NET: Registered protocol family 24
[ 9.040000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 9.050000] cfg80211: Calling CRDA for country: US
[ 9.050000] cfg80211: Regulatory domain changed to country: US
[ 9.060000] cfg80211:DFS Master region: FCC
[ 9.060000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 9.080000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 9.090000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 9.100000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 9.110000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 16.220000] device eth0 entered promiscuous mode
[ 18.620000] eth0: link up (100Mbps/Full duplex)
[ 18.620000] br-lan: port 1(eth0) entered forwarding state
[ 18.630000] br-lan: port 1(eth0) entered forwarding state
[ 18.770000] device wlan0 entered promiscuous mode
[ 18.780000] br-lan: port 2(wlan0) entered forwarding state
[ 18.780000] br-lan: port 2(wlan0) entered forwarding state
[ 19.620000] br-lan: port 2(wlan0) entered disabled state
[ 20.630000] br-lan: port 1(eth0) entered forwarding state
[ 24.930000] br-lan: port 2(wlan0) entered forwarding state
[ 24.930000] br-lan: port 2(wlan0) entered forwarding state
[ 26.930000] br-lan: port 2(wlan0) entered forwarding state
procd: Instance odhcpd::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
[ 50.920000] apqos: module license 'unspecified' taints kernel.
[ 50.930000] Disabling lock debugging due to kernel taint
[ 51.110000] original value = 0
[ 51.110000] this is write operation, current value = 0
[ 51.240000] original value =
[ 51.250000] this is write operation, current value = wlan0
procd: - init complete -
Welcome!
Username: root
Password:
Access denied
Username: 自己顶起来 还是上编程器吧简单快捷 还管用 上编程器吧简单快捷 还管用 没工具取不下芯片，怕到时又安不上 https://www.anywlan.com/thread-441004-1-1.html
https://www.anywlan.com/thread-435079-1-1.html
善用论坛搜索 取下芯片，需要热风枪吧 幽意 发表于 2022-6-19 09:53
https://www.anywlan.com/thread-441004-1-1.html
https://www.anywlan.com/thread-435079-1-1.html
善用 ...
看过了，只可用于能解锁的机器，我这个没解锁的 本帖最后由 gablove 于 2022-6-26 11:29 编辑
这个uboot 无解锁选项，我也是一样百米 熬了半天没有效果 最后上了编程器 刷的，
有个群有人出固件15元 不过那时编程器已经在路上了 我就没买 如果你需要可以问一下那个人
gablove 发表于 2022-6-24 23:02
这个uboot 无解锁选项，我也是一样百米 熬了半天没有效果 最后上了编程器 刷的，
有个群有人出固件15元 不 ...
我前后买了三个，第一个无法解锁。第二个，刷了BREED，结果想退回，刷了个网上下的原版BIN文件，成砖。又买了个刷好的。为了救活前两个，现在重新买了个编程器:dizzy: pzq130 发表于 2022-6-25 21:41
我前后买了三个，第一个无法解锁。第二个，刷了BREED，结果想退回，刷了个网上下的原版BIN文件，成砖。又 ...
唉 最终都逃离不过编程器按教程 用夹子就ok 不用拆flash
页:
[1]
2