111111 发表于 2010-2-26 20:54

楼上的问题我还真没研究过

fengyuxiong 发表于 2010-2-26 22:24

谢谢楼主， 正在找这方面的东西！

09ace 发表于 2010-2-27 22:00

下来看看，谢谢！

leo3518 发表于 2010-3-6 02:35

我始终不知道怎么全面使用BT4

hjpxc 发表于 2010-3-6 07:56

支持一下。希望有用的朋友设置一下

arbel 发表于 2010-3-6 20:25

诶……居然用这种低级的方法骗钱……

rr258369 发表于 2010-3-8 11:09

:)eth1      Link encap:EthernetHWaddr 00:21:00:a7:38:b2
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
          Interrupt:17

lo      Link encap:Local Loopback
          inet addr:127.0.0.1Mask:255.0.0.0
          UP LOOPBACK RUNNINGMTU:16436Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)

root@bt:~# ifconfig -a eth1 up
root@bt:~# ifconfig -a eth1 up
root@bt:~# ifconfig
eth1      Link encap:EthernetHWaddr 00:21:00:a7:38:b2
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
          Interrupt:17

lo      Link encap:Local Loopback
          inet addr:127.0.0.1Mask:255.0.0.0
          UP LOOPBACK RUNNINGMTU:16436Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)

root@bt:~# airmon-ng start eth1 6


Interface       Chipset         Driver

eth1            Unknown               wl (monitor mode enabled)

root@bt:~# airodump-ng eth1
ioctl(SIOCSIWMODE) failed: Invalid argument

ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead.Make
sure RFMON is enabled: run 'airmon-ng start eth1 <#>'
Sysfs injection support was not found either.

root@bt:~# airmon -ng start wl 6
bash: airmon: command not found
root@bt:~# airmon -ng eth1
bash: airmon: command not found
root@bt:~# airmon-ng start wl


Interface       Chipset         Driver

eth1            Unknown               wl

root@bt:~# airodump-ng wl
Interface wl:
ioctl(SIOCGIFINDEX) failed: No such device
root@bt:~# airodump-ng eth1
ioctl(SIOCSIWMODE) failed: Invalid argument

ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead.Make
sure RFMON is enabled: run 'airmon-ng start eth1 <#>'
Sysfs injection support was not found either.

root@bt:~# airmon-ng start eth1


Interface       Chipset         Driver

eth1            Unknown               wl (monitor mode enabled)

root@bt:~# airodump-ng eth1
ioctl(SIOCSIWMODE) failed: Invalid argument

ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead.Make
sure RFMON is enabled: run 'airmon-ng start eth1 <#>'
Sysfs injection support was not found either.

root@bt:~# airodump-ng start eth1 1
"airodump-ng --help" for help.
root@bt:~# airmon-ng start eth1 1


Interface       Chipset         Driver

eth1            Unknown               wl (monitor mode enabled)

root@bt:~# airdump-ng eth1
bash: airdump-ng: command not found
root@bt:~# airodump-ng eth1
ioctl(SIOCSIWMODE) failed: Invalid argument

ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead.Make
sure RFMON is enabled: run 'airmon-ng start eth1 <#>'
Sysfs injection support was not found either.

root@bt:~# airdump-ng start wl
bash: airdump-ng: command not found
root@bt:~# airodump-ng wl
Interface wl:
ioctl(SIOCGIFINDEX) failed: No such device
root@bt:~#

zhangqh828 发表于 2010-3-8 12:44

:victory::victory:

zcming 发表于 2010-3-8 13:29

:o赚个金币 买个主题

3w3g 发表于 2010-3-8 13:44

啥都是金币啊～～

fyld2003 发表于 2010-3-13 22:05

支持一下,学习一下

xmlyx 发表于 2010-3-13 22:14

嗨，不知道啥意思。还不如出一个英文命令的教程。
页: 1 2 3 4 [5] 6 7
查看完整版本: BT4 正式版 设置中文的命令