[原创] 招募小白鼠与开发人员

[复制链接]

lintel

198 回帖	5618 积分	70 小时在线时间

中校

Embedded Linux砖家

注册时间: 2008-10-23

金币: 4923 个

威望: 55 个

荣誉: 12 个

发消息

尚未签到

发表于 2009-4-4 10:42 |显示全部楼层

本帖最后由 lintel 于 2009-4-4 19:36 编辑

现在盒子(MGB100)的功能正在慢慢完善，Linux 2.6.22.1也在加紧开发中（已经有了小白版本）。
准备招募试验用的小白以及有兴趣完善，发掘盒子新功能的兄弟。
         目前盒子开发的进展：
   成功编译了linux2.6.22.1内核，但是驱动极不完善。
   使用新的BootLoader---- Redboot
   成功实现了64M内存的修改。

   入围条件：

                     必需自备：MGB100主板一个

            开发人员：
                     1.自己有JTAG工具，有能力通过JTAG恢复变砖的盒子。
                     2.对Linuz内核有一定研究，能自己编译，使用内核。
                     3.有较多的空余时间

            测试人员：
                     1.自己有JTAG工具，能自己修复变砖的盒子。
                     2.有一定的Linux操作能力

         测试用小白：
                     1.具备TTL串口工具（TTL to RS232）
                     2.有一定的Linux操作能力

有意者加QQ群：32504136

进入后请选择自己适合的分组。比如选择测试人员的。请再群名片上加前缀：测试--+你的名字

顺便送几张大家有兴趣的截图：

内核启动信息：

(none):/proc# dmesg
Linux version 2.6.22.1 ([email=root@andLinux]root@andLinux[/email]) (gcc version 3.3.6) #6 Fri Apr 3 07:33:22 EDT 2009
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000002000000 (usable)
32MB LOWMEM available.
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Zone PFN ranges:
  DMA          0 ->    4096
  Normal    4096 ->    8192
early_node_map[1] active PFN ranges
0:       0 ->    8192
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 32 pages used for memmap
  Normal zone: 4064 pages, LIFO batch:0
DMI not present or invalid.
Using APIC driver default
Allocating PCI resources starting at 10000000 (gap: 02000000:fe000000)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS0,38400 root=/dev/hda1 rw
No local APIC present or hardware disabled
mapped APIC to ffffd000 (01041000)
Initializing CPU#0
PID hash table entries: 128 (order: 7, 512 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26420k/32768k available (1782k kernel code, 5960k reserved, 919k data, 164k init, 0k highmem)
virtual kernel memory layout:
fixmap  : 0xfffba000 - 0xfffff000 ( 276 kB)
vmalloc : 0xc2800000 - 0xfffb8000 ( 983 MB)
lowmem  : 0xc0000000 - 0xc2000000 (  32 MB)
   .init : 0xc03a6000 - 0xc03cf000 ( 164 kB)
   .data : 0xc02bd8e6 - 0xc03a3840 ( 919 kB)
   .text : 0xc0100000 - 0xc02bd8e6 (1782 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 50.43 BogoMIPS (lpj=100864)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After all inits, caps: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: 486
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Cannot allocate resource region 0 of device 0000:00:01.0
Time: pit clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2560k freed
NTFS driver 2.1.28 [Flags: R/O].
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
r6040: RDC R6040 net driver, version 0.13 (24Aug2006)
r6040: RDC R6040 net driver, version 0.13 (24Aug2006)
PCI: Setting latency timer of device 0000:00:08.0 to 64
r6040: RDC R6040 net driver, version 0.13 (24Aug2006)
PCI: Setting latency timer of device 0000:00:09.0 to 64
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
IT8212: IDE controller at PCI slot 0000:00:04.0
IT8212: chipset revision 17
it8212: forcing bypass mode.
it821x: controller in pass through mode.
IT8212: 100% native mode on irq 9
ide0: BM-DMA at 0x4400-0x4407, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
hda: SAMSUNG MP0402H, ATA DISK drive
hda: selected mode 0x45
ide0 at 0x4000-0x4007,0x4102 on irq 9
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 78242976 sectors (40060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda4
ehci_hcd 0000:00:0a.1: EHCI Host Controller
ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.1: irq 14, io mem 0xc1000000
ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0a.0: OHCI Host Controller
ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0a.0: irq 15, io mem 0xc1001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042.c: Warning: Keylock active.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
RAMDISK: Couldn't find valid RAM disk image starting at 0.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 164k freed
Adding 134904k swap on /dev/hda4.  Priority:-1 extents:1 across:134904k
EXT2-fs: quota operations not supported.
EXT2-fs: quota operations not supported.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access    Generic  USB Flash Disk 7.76 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete
usb 1-1: USB disconnect, address 2
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: CD-ROM          Lintel DVD-RAM       1.00 PQ: 0 ANSI: 2
usb-storage: device scan complete
usb 1-1: USB disconnect, address 3
usb 1-1: new high speed USB device using ehci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access    Generic  USB Flash Disk 7.76 PQ: 0 ANSI: 2
sd 2:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 2:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete

BootLoader, Linux, 成功, 盒子, 开发