优酷路由宝刷磊科no1

pxjiangqi205

优酷路由宝刷磊科no1

首先感谢论坛各大神，大神名号就不提了，总之感谢。然后本人小白，请勿喷。最后，刷机变砖本人不负任何责任。怕变砖请勿试。

几个月前就准备买极1s，准备刷成磊科no1、或者如意云，后来优酷路由宝公测，幸运的是抢上一台。

有大神将优酷路由宝刷成潘多拉（大神真给力啊，代表无数小白表示感谢），本人猜想，既然优酷路由宝的cpu内存等和磊科no1如意相似，那也应该能刷成磊科no1了。于是开始刷机。

第一步，安照http://www.right.com.cn/forum/thread-161802-1-1.html 这个贴子刷u-boot，之所以按照这个贴子，是因为这个贴子，说得很清楚，明白，其它大神把刷机过程说得要隐晦一点。大神勿喷！

重点来了

1、刷完u-boot后，

设置电脑ip地址为

2、电脑网卡上的网线接路由宝三个网线端口的中间的那个，因为刷完磊科no1的固件后，wan端口和lan1会对调。

3、地址栏输入192.168.1.1 进入uboot恢复界面。我用360极速浏览器进入备份页面，先备份了eeprom，别问我为何要备份，因为我是小白，只是想备份一下。

恢复时，选择刷机包中编程器固件，之所以选择这个固件是因为，编程器固件涉及到分区问题（个人猜测）。下载链接http://pan.baidu.com/s/1kTGaByf

4、刷完约3分钟，路由会自己重启，一定要等它自动重启哦。这一点我也是猜的。

5、按lan1接从调制解调器接出的网线，中间lan2，和wan 接局域网电脑的思路，接好网线。地址栏输入192.168.1.1进入路由器管理后台。登陆密码guest

6、找到设备管理，软件升级、手动升级。选择升级文件，浏览文件选择要升级的文件。下载链接http://pan.baidu.com/s/1hqlE6oc

升级完成后，安照正常的上网设置流程设置完后 就可以使用了

7、升级完成后，绑定磊科帐号，可使用磊科插件。共有20多个可使用的插件，我半个小时后，依然能正常安装使用插件，这些插件比较实用。

8、不足之处，为何我的led不亮了？不过没关系，我还闲灯太闪呢。路由宝有32m的rom空间，刷完后，8m用于系统，8m用于插件安装，基本够用，还有16m没有识别，如果有大神能识别就好了

内置Sd卡可正常识别使用，这一点还是不错的，远程下载很方便。

最后发上图片，明天有时间了再试一下，能不能刷如意云。

补充内容 (2016-1-24 12:16):
重发插件 http://pan.baidu.com/s/1ZOuxK
编程器固件 http://pan.baidu.com/s/1be7QX4
升级固件http://pan.baidu.com/s/1geyaCdt

yaojbo8

pxjiangqi205 发表于 2015-3-21 18:40
http://downloads.openwrt.org.cn/PandoraBox/YouKu_YK1/u-boot/u-boot-pandorabox-yk1-20150113.bin  这 ...

TTL成功，但是无法中断，不能再继续下去了，怎么办？

U-Boot 1.1.3 (Nov 26 2013 - 15:10:32)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 19 0 0 (40190000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.1.2.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Nov 26 2013  Time:15:10:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
rvlan initialization done
welcome!
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:50
   Image Name:   No1;;netcore
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6779200 Bytes =  6.5 MB
   Load Address: 80000000
   Entry Point:  8000c310
raspi_read: from:50050 len:677140
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 128

Starting kernel ...


LINUX started...

THIS IS ASIC
to 580 MHz

MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00040208
Readback ErrCtl register=00040208
Memory: 124296k/131072k available (3621k kernel code, 6776k reserved, 994k data, 184k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80467f18, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocoPPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 242
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
gpio_test_proc create proc success
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
loop: module loaded
deice id : ef 40 19 0 0 (40190000)
Warning: un-recognized chip ID, please update SPI driver!
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
find key:hsqs from 0xbc050000 to 0xbc800000
offset:0x0000000000000000 size:0x0000000000000000 name:ALL
offset:0x0000000000000000 size:0x0000000000030000 name:Bootloader
offset:0xffffffffffffffff size:0x0000000000010000 namearameter2
offset:0xffffffffffffffff size:0x0000000000010000 name:Factory
offset:0xffffffffffffffff size:0x0000000000000000 name:Kernel
offset:0xffffffffffffffff size:0x00000000007b0000 name:RootFS
offset:0x0000000000050000 size:0x00000000007b0000 name:Kernel_RootFS
offset:0xffffffffffffffff size:0x0000000000060000 name:Kernel_mini
offset:0xffffffffffffffff size:0x0000000000050000 namearameter1
offset:0xffffffffffffffff size:0x0000000000800000 name:Application
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "arameter2"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x0000001e5190 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x0000001e5190-0x000000750000 : "RootFS"
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x000000050000-0x000000750000 : "Kernel_RootFS"
0x000000750000-0x0000007b0000 : "Kernel_mini"
0x0000007b0000-0x000000800000 : "arameter1"
0x000000800000-0x000001000000 : "Application"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for cp210x
usbcore: registered new interface driver cp210x
cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
MTK MSDC device init.
mtk-sd: MediaTek MT6575 MSDC Driver
hbwrr_reg:0
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3000 buckets, 24000 max)
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
net sniffer init ok.
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2273> PID<kworker/u:1><0x1e>
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
NETCORE fastpath V0.03
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 184k freed

^C

init started:  BusyBox v1.1.2 (2014.06.18-09:03+0000) multi-call binary
Starting pid 39, console /dev/ttyS1: '/etc/rcS'
^C
Please press Enter to activate this console.
Starting pid 41, console /dev/ttyS1: '/bin/sh'


BusyBox v1.1.2 (2014.06.18-09:03+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ $

pxjiangqi205

正常运行8个小时，led灯有小bug，不影响使用。好像要刷回去，真的难哎，估计要上编程器了。

补充内容 (2015-10-14 10:40):
有机友要装好插件的编程器固件，现在上传一个。路由后台192.168.1.1 密码guest  迅雷远程激活码不一定能显示，自已解决。其它bug自测。看好了，这是优酷路由宝第三批刷no1的编程器备份，一共32m。请自行修改mac  ...

补充内容 (2015-10-14 10:41):
http://pan.baidu.com/s/1hqCpg6w   CRC32: 32C34060
MD5: 9F5911707BA7045E219E1DD3A0B395F6
SHA-1: FEA9BB461D0CCE4BDA88FCD4E2A2D9036FC63238


补充内容 (2017-4-26 20:48):
链接: https://pan.baidu.com/s/1geFd0B5 密码: 26ty

biyanping

把你的路由宝固件共享下吧。

zizhi4818

首先感谢楼主的分享，我也准备刷来玩玩，因为我一下子买了两个。因为这路由器的配置不错。
还有再问一些小白的问题，
1、怎样用360极速浏览器进入备份页面？
2、为什么要使用编程器固件？

pxjiangqi205

zizhi4818 发表于 2015-3-20 16:00
首先感谢楼主的分享，我也准备刷来玩玩，因为我一下子买了两个。因为这路由器的配置不错。
还有再问一些小 ...

设置电脑ip地址后，地址栏输入192.168.1.1。ie也应该可以的。
进入uboot 后，要恢复还是备份，页面上有提示，先刷编程器固件，涉及到分区问题，这只是个人理解，你可试试一下，直接刷最新固件。

火火的爱

求备份啊

火火的爱

ASUS N14U 300M 双wan for 如意云RY1 修复LED
http://www.anywlan.com/forum.p ... 191&fromuid=1025810
(出处: http://www.anywlan.com/)
不知道这个能不能刷入呢？是适配如意云的，灯也改过来了

yaojbo8

已经成功刷磊科NO1 我现在要刷回去怎么办？刷成OP
telnet 连上了，

如何刷其他固件？

yksky

看恩山那 好像要先备份 然后可以刷回 当然那里是刷潘多拉

AIRSHAPE

qos正常不                 

yaojbo8

求刷回不死UBOOT.我还要刷OP。

现在磊科固件，我怎么刷不死UBOOT?

pxjiangqi205

yaojbo8 发表于 2015-3-21 11:22
已经成功刷磊科NO1 我现在要刷回去怎么办？刷成OP
telnet 连上了，

目前可行办法是，拆开后盖刷通过ttl刷不死uboot，或者上编程器